banner_page

INA207AIDG4

14 Terminations12V 14 Pin INA207 Current regulator-40°C~125°C Min 2.7V Max 18V


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-INA207AIDG4
  • Package: 14-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 388
  • Description: 14 Terminations12V 14 Pin INA207 Current regulator-40°C~125°C Min 2.7V Max 18V (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 14-SOIC (0.154, 3.90mm Width)
Number of Pins 14
Weight 129.387224mg
Operating Temperature -40°C~125°C
Packaging Tube
JESD-609 Code e4
Part Status Active
Moisture Sensitivity Level (MSL) 2 (1 Year)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
HTS Code 8542.39.00.01
Subcategory Operational Amplifier
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Supply Voltage 12V
Terminal Pitch 1.27mm
Base Part Number INA207
Function Current Monitor
Output Type OPEN-DRAIN
Power Supplies 12V
Max Supply Voltage 18V
Min Supply Voltage 2.7V
Voltage - Input -16V~80V
Nominal Supply Current 2.8mA
Current - Output 1mA
Accuracy ±3.5%
Response Time 1300 ns
Slew Rate 1 V/μs
Amplifier Type COMPARATOR
Bandwidth 300 kHz
Average Bias Current-Max (IIB) 16μA
Bias Current-Max (IIB) @25C 0.01μA
Sensing Method High-Side
Input Offset Voltage-Max 2500μV
Height Seated (Max) 1.75mm
Length 8.65mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

INA207AIDG4 Overview


Buck boost converter is embedded in the Tube package.In the same manner as 14-SOIC (0.154, 3.90mm Width), voltage regulator is packaged.Surface Mount is used to mount this current regulator on the board.Temperatures should not exceed -40°C~125°C during operation.As far as input voltage goes, current regulator supports the value of -16V~80V.An example of this is the 14 termination, which is a procedure in which a transmission line is terminated with a voltage regulator that is equal in impedance to the line characteristics.Current regulator belongs to INA207 family.14-pins are pronged contacts that form part of a computer's or other constant current regulator's signal interface.Surface Mount is responsible for mounting this current regulator.Providing the constant current is powered by a 12VV power source, the constant current should be able to function.In addition to the maximum design flexibility that 1mA provides, its output current is also quite high.There is a maximum voltage to be supplied to 18V by it.Operational Amplifier, which is a part that contains all of these current regulations, is included in this part.As long as the supply voltage is lower than 2.7V, it will operate correctly.This electrical buck boost converter is an amplifier of type COMPARATOR.A 12V power supply is used to power the boost converter.

INA207AIDG4 Features


Tube package
INA207 family
The maximal supply voltage of 18V
12V power supplies

INA207AIDG4 Applications


There are a lot of Texas Instruments INA207AIDG4 Current Regulation/Managements applications.

  • Diesel injection controls
  • Smart battery packs
  • Over-current measurement
  • Over-current protection
  • Transmission controls
  • Battery management
  • Current sensing
  • Over current monitor
  • Suspension controls
  • Battery chargers

Write a review

Note: HTML is not translated!
    Bad           Good