INA213AQDCKRQ1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 2.494758mg |
| Manufacturer Package Identifier | DCk(R-PDSO-G6) |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | INA213 |
| Pin Count | 6 |
| Number of Elements | 1 |
| Nominal Supply Current | 115μA |
| Accuracy | 1 % |
| Current - Supply | 65μA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Current Sense |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 28μA |
| Voltage - Supply, Single/Dual (±) | 2.7V~26V |
| Input Offset Voltage (Vos) | 100μV |
| Gain Bandwidth Product | 80kHz |
| Unity Gain BW-Nom | 80 kHz |
| Voltage Gain | 33.98dB |
| Average Bias Current-Max (IIB) | 35μA |
| Power Supply Rejection Ratio (PSRR) | 140dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 5μV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 35μA |
| Programmable Power | NO |
| Wideband | NO |
| Voltage Gain-Nom | 50 |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
INA213AQDCKRQ1 Overview
Op amp is packaged in 6-TSSOP, SC-88, SOT-363 case. The instrumentation amplifier in this picture is of the Current Sense-type. A Tape & Reel (TR) case is used for delivering the op amp. It is estimated that there will be at least 6 terminations this year. The total number of pins on linear amplifier is 6. This linear amplifier should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. There are 6 pins on this chip. Regarding input offset voltage, buffer amplifier rates 100μV voltage. This electronic part is best mounted with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. Op amp is a member of the 33.98dB's 33.98dB family. There are 1 elements in this buffer amplifier. The linear amplifier is packaged by using a TR axis. There is a recommendation that this electrical part be used with a supply with 65μA current rating. In this case, Automotive, AEC-Q100 represents the instrumentation amplifiers' series number.
INA213AQDCKRQ1 Features
6 Pins
supply voltage of 5V
33.98dB voltage gain
INA213AQDCKRQ1 Applications
There are a lot of Texas Instruments INA213AQDCKRQ1 Instrumentational OP Amps applications.
- Exponential operation circuits
- Large motor controllers
- High/low-pass filter circuit
- Vehicle electronics
- Band-pass filter
- Polarized electrodes
- Proportional counter tubes
- Voltage regulation circuit
- Precision measurement
- Signal transformation
