INA2141UA/1K
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 420.395078mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10GOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | INA2141 |
| Pin Count | 16 |
| Number of Elements | 6 |
| Number of Circuits | 2 |
| Nominal Supply Current | 1.6mA |
| Quiescent Current | 750μA |
| Current - Supply | 1.5mA |
| Slew Rate | 4V/μs |
| Amplifier Type | Instrumentation |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 2nA |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±2.25V~18V |
| Input Offset Voltage (Vos) | 250μV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Average Bias Current-Max (IIB) | 0.005μA |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 20μV |
| Current - Output / Channel | 15mA |
| -3db Bandwidth | 200kHz |
| Dual Supply Voltage | 15V |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Offset Current-Max (IIO) | 0.01μA |
| Voltage Gain-Min | 10 |
| Input Voltage Noise Density | 8nV/sqrt Hz |
| Voltage Gain-Nom | 10 |
| Voltage Gain-Max | 100 |
| Height | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
INA2141UA/1K Overview
A 16-SOIC (0.295, 7.50mm Width) case is used to package the op amp. A Instrumentation-type buffer amplifier is shown here. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. There have been a total of 16 terminations over the past year. In total, there are 16 pins on this op amp ic. This linear amplifier should be powered by an 15V battery. It has 16 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 250μV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . The buffer amp consists of 2 circuits in total. According to the specifications of the buffer op amp, the operating supply voltage is rated at 6. An buffer amplifier is packed in a TR-shape according to the design. As a result, it is recommended that a power supply of 1.5mA be used with this electronic part. Currently, linear amplifier is operating with a quiescent current of 750μA. To conduct electronic part voltage gain higher than 10. In order for the buffer amplifier resistance to remain within the 10GOhm range, the device should be tested.
INA2141UA/1K Features
16 Pins
supply voltage of 15V
Resistance of 10GOhm
INA2141UA/1K Applications
There are a lot of Texas Instruments INA2141UA/1K Instrumentational OP Amps applications.
- High speed sample
- Car stereo
- Information processing
- Division circuits
- Non-polarized electrodes
- Scintillation detectors
- Mobile phone
- Communication
- Thermocouples
- Signal amplification
