IPS1011SPBF
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-3, D2Pak (2 Leads + Tab), TO-263AB |
| Number of Pins | 3 |
| Supplier Device Package | D2PAK |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Published | 2006 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Termination | SMD/SMT |
| Resistance | 10mOhm |
| Max Operating Temperature | 150°C |
| Min Operating Temperature | -40°C |
| Power Rating | 3.1W |
| Max Power Dissipation | 3.1W |
| Current Rating | 18A |
| Base Part Number | IPS1011SPBF |
| Number of Outputs | 1 |
| Output Voltage | 28V |
| Output Type | N-Channel |
| Max Output Current | 6.5A |
| Operating Supply Voltage | 5.5V |
| Interface | On/Off |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Current - Output (Max) | 6.5A |
| Output Configuration | Low Side |
| Power Dissipation | 3.1W |
| Output Current | 85A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Clamping Voltage | 36V |
| Output Current per Channel | 6.5A |
| Rise Time | 50μs |
| Drain to Source Voltage (Vdss) | 36V |
| Fall Time (Typ) | 70 μs |
| Nominal Input Voltage | 5.5V |
| Continuous Drain Current (ID) | 6.5A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 28V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Dual Supply Voltage | 28V |
| Rds On (Typ) | 10mOhm |
| Nominal Vgs | 1.7 V |
| Height | 4.826mm |
| Length | 10.668mm |
| Width | 9.65mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
IPS1011SPBF Overview
As you can see, it's packaged in the way of a Tube.The TO-263-3, D2Pak (2 Leads + Tab), TO-263AB package contains it.The mounting type of the LED driver is Surface Mount.This switch is of type General Purpose.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.The LED driver is equipped with 1 outputs.Operation is based on Not Required supply voltage.A maximum output voltage of N-Channel volts can be achieved by this LED driver.It belongs to the family IPS1011SPBF.In order to operate, the 3 pins are used.The maximum output of the LED driving board is 6.5AV.It is necessary to reduce the maximum output current to 6.5A to meet the operation criteria.This lighting driver is mounted in the way of Surface Mount.Currently, the LED driving board has a resistance of 10mOhm ohms.The output current is set to 85A in this case.In order to achieve the best efficiency, the supply voltage should be set to 5.5V.For stable operation, the maximum operating temperature should be 150°C°C.In order to ensure reliability, it must operate at a minimum temperature of -40°C degrees Celsius.It can handle a voltage of 5.5VV as its maximum supply voltage.Supply voltages as low as 4.5VV are possible.
IPS1011SPBF Features
Resistance of 10mOhm
IPS1011SPBF Applications
There are a lot of Infineon Technologies IPS1011SPBF Power Switches ICs applications.
- Mobile Communication Devices
- Solid State Drivers
- USB Ports/Hubs
- Gaming
- Notebook and Tablet Computers
- Wearable Devices
- Smart Phones, Feature Phones
- Telecom and Network Systems
- Portable Devices
- Solid-State Drives
