IPS1031PBF
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | TO-220-3 |
| Number of Pins | 3 |
| Supplier Device Package | TO-220AB |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Published | 2006 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Termination | Through Hole |
| Type | Switch |
| Resistance | 40mOhm |
| Max Operating Temperature | 150°C |
| Min Operating Temperature | -40°C |
| Power Rating | 25W |
| Max Power Dissipation | 25W |
| Current Rating | 4A |
| Base Part Number | IPS1031PBF |
| Number of Outputs | 1 |
| Output Voltage | 28V |
| Output Type | N-Channel |
| Max Output Current | 9.5A |
| Operating Supply Voltage | 36V |
| Voltage | 5.5V |
| Interface | On/Off |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Current - Output (Max) | 9.5A |
| Current | 9.5A |
| Output Configuration | Low Side |
| Power Dissipation | 25W |
| Output Current | 18A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Clamping Voltage | 36V |
| Output Current per Channel | 9.5A |
| Rise Time | 20μs |
| Drain to Source Voltage (Vdss) | 36V |
| Fall Time (Typ) | 15 μs |
| Nominal Input Voltage | 5.5V |
| Continuous Drain Current (ID) | 6A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 28V Max |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Dual Supply Voltage | 28V |
| Rds On (Typ) | 40mOhm |
| Drain to Source Resistance | 40mOhm |
| Nominal Vgs | 1.7 V |
| Height | 9.02mm |
| Length | 10.6426mm |
| Width | 4.826mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
IPS1031PBF Overview
As you can see, it's packaged in the way of a Tube.In the TO-220-3 package, it is included.It has been mounted as Through Hole on the LED driver.There is a switch type of General Purpose.The temperature should be set to -40°C~150°C TJ to ensure reliable functioning.It is possible to use 1 outputs in the lighting driver.A supply voltage of Not Required is required for it to operate.There is a maximum output voltage of N-Channel volts on this LED driver.As you can see, it comes from the IPS1031PBF family.In order to operate, the 3 pins are used.There is a maximum output of 9.5AV from the LED driver.Maximum output current falls to 9.5A when operation criteria are met.In this case, it is mounted in the way of Through Hole.Currently, the LED driving board has a resistance of 40mOhm ohms.This case has the output current set to 18A.Optimal efficiency requires a voltage of 36V.For stable operation, the maximum operating temperature should be 150°C°C.The LED driver must work at a minimum temperature of -40°C degrees Celsius in order to remain reliable.It can handle a voltage of 5.5VV as its maximum supply voltage.It can operate at low supply voltages, such as 4.5V volts.Electrical components classified as Switch are included in this category.
IPS1031PBF Features
Resistance of 40mOhm
IPS1031PBF Applications
There are a lot of Infineon Technologies IPS1031PBF Power Switches ICs applications.
- Set-top-box
- Hot Swap
- USB Ports/Hubs
- Gaming
- USB Protection
- Wireless Modem Data Cards
- USB3.1 Power Delivery
- PC Cards
- Portable GPS Device
- Wearable Devices
