banner_page

ISL28130CHZ-T7A

15mA per Channel 250pA 125 dB Instrumentational OP Amps 5V SOT-23


  • Manufacturer: Intersil (Renesas Electronics America)
  • Nocochips NO: 391-ISL28130CHZ-T7A
  • Package: SOT-23
  • Datasheet: PDF
  • Stock: 310
  • Description: 15mA per Channel 250pA 125 dB Instrumentational OP Amps 5V SOT-23(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Package / Case SOT-23
Number of Pins 5
Published 2005
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1
Number of Terminations 5
ECCN Code EAR99
Terminal Finish Matte Tin (Sn) - annealed
Max Operating Temperature 70°C
Min Operating Temperature 0°C
Subcategory Operational Amplifier
Packing Method TAPE AND REEL
Technology CMOS
Terminal Form GULL WING
Number of Functions 1
Supply Voltage 5V
Operating Supply Voltage 5V
Temperature Grade COMMERCIAL
Number of Circuits 1
Max Supply Voltage 5.5V
Min Supply Voltage 1.8V
Operating Supply Current 20μA
Nominal Supply Current 25μA
Slew Rate 0.2 V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type OPERATIONAL AMPLIFIER
Common Mode Rejection Ratio 125 dB
Current - Input Bias 250pA
Output Current per Channel 15mA
Supply Type Dual, Single
Input Offset Voltage (Vos) 5μV
Bandwidth 400 kHz
Gain Bandwidth Product 400 kHz
Unity Gain BW-Nom 400 kHz
Voltage Gain 150dB
Power Supply Rejection Ratio (PSRR) 138dB
Low-Offset YES
Frequency Compensation YES
Max Dual Supply Voltage 2.75V
Low-Bias YES
Micropower YES
Min Dual Supply Voltage 900mV
Programmable Power NO
Length 2.9mm
Radiation Hardening No
REACH SVHC Unknown
RoHS Status RoHS Compliant
Lead Free Lead Free

ISL28130CHZ-T7A Overview


The linear amplifier is packaged in a SOT-23 case. OPERATIONAL AMPLIFIER-type instrumentation amplifiers are used in this application. During the past two weeks, there have been close to 5 terminations. I would like to remind you that this buffer op amp should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. There are 5 pins on this chip. Op amp ic rates 5μV for input offset voltage. Using a supply current of 20μA , this buffer op amp will be able to operate. It is recommended to keep the voltage gain at 150dB at all times. On this instrumentation amplifier, there are 1 circuits that are connected together. In order for this buffer op amp to function, it should have a temperature of at least 0°C degrees Celsius. Instrumentation amplifier shouldn't be used above 70°C . The operating supply voltage of instrumentation amplifier is rated 5V voltage. This linear amplifier pack is based on the TAPE AND REEL axis. I would like to point out that this electrical component is capable of working from a voltage below 5.5V as far as the power supply is concerned. To keep the buffer amps' supply voltage higher than 1.8V. As a general rule, you should conduct this electronic component under dual supply voltages of 2.75V volts.

ISL28130CHZ-T7A Features


supply voltage of 5V
150dB voltage gain

ISL28130CHZ-T7A Applications


There are a lot of Intersil (Renesas Electronics America) ISL28130CHZ-T7A Instrumentational OP Amps applications.

  • Logarithmic operation circuits
  • Scintillation detectors
  • Gaming industry
  • Communication device
  • Information processing
  • Portable electronic products powered by batteries
  • Measurements of Wheatstone bridge
  • Medical instruments
  • Polarized electrodes
  • Commercial audio systems

Write a review

Note: HTML is not translated!
    Bad           Good