ISL28291FUZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | MSOP |
| Number of Pins | 10 |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Temperature Grade | AUTOMOTIVE |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 2.6mA |
| Supply Current-Max | 3.9mA |
| Slew Rate | 17 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 3μA |
| Output Current per Channel | 130mA |
| Input Offset Voltage (Vos) | 270μV |
| Bandwidth | 61MHz |
| Voltage Gain | 98dB |
| Average Bias Current-Max (IIB) | 7μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | NO |
| -3db Bandwidth | 61MHz |
| Bias Current-Max (IIB) @25C | 6μA |
| Input Voltage Noise Density | 1.7nV/sqrt Hz |
| Input Noise Current Density | 1.8pA/sqrt Hz |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
ISL28291FUZ Overview
There is a MSOP case in which the instrumentation amplifier is packaged. An op amp of this type is a OPERATIONAL AMPLIFIER-type. It is estimated that there will be 10 terminations in the next few months. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. It has 10 pins that make up the linear amplifier. Regarding input offset voltage, op amp rates 270μV. A supply current of 2.6mA can be used to operate this linear amplifier. There should be no change in the voltage gain at 98dB. The buffer amp consists of 2 circuits in total. In order for this buffer op amp to function, it should have a temperature of at least -40°C degrees Celsius. You should not use op amp above 125°C . The operating supply voltage of the buffer op amp is rated at 5V. The electrical part is capable of being powered by a voltage of under 5.5V, which means that it can be used with any voltage supply. A voltage of 3V or higher is recommended for the linear amplifier's supply voltage.
ISL28291FUZ Features
supply voltage of 5V
98dB voltage gain
ISL28291FUZ Applications
There are a lot of Intersil (Renesas Electronics America) ISL28291FUZ Instrumentational OP Amps applications.
- Proportional counter tubes
- Portable docking station
- pH (acidity)
- Scintillation detectors
- High-frequency data acquisition systems
- Video amplifiers
- Portable media players
- Ultrasound transducers
- Weighing systems
- Video computer boards
