ISL43140IBZ-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Packaging | Tape & Reel |
| Published | 2001 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| Resistance | 65Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 16, 16 |
| JESD-30 Code | R-PDSO-G16 |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 50nA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 70 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| Dual Supply Voltage | 5V |
| On-state Resistance Match-Nom | 2Ohm |
| Switch-on Time-Max | 80ns |
| Switch-off Time-Max | 30ns |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
ISL43140IBZ-T Overview
Shipping overseas is convenient with the electronic component packed in SOIC. Advanced packaging method Tape & Reel is used to provide high reliability. In total, there are 16 terminations. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. An injection of 16, 16 pins is performed into the body of the electrical component. As far as internal resistance is concerned, it has 65Ohm. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. The switch device would be able to operate with 50nA current. A digital multiplexer may suffer damage if voltage is applied above 1μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. In the case of dual power supplies, you should connect at least 2V. Temperatures over 85°C should not be allowed for the multiplexer to operate. 4-bits are supported.
ISL43140IBZ-T Features
1 Channels
50nA Supply Current
4-Bit
ISL43140IBZ-T Applications
There are a lot of Intersil (Renesas Electronics America) ISL43140IBZ-T Analog Switches & Multiplexers ICs applications.
- Communication systems
- Sample hold systems
- Video switching
- Intelligent PBX
- SDH
- T1/E1 Terminals
- Communication systems
- PDAs
- Audio signal routing
- Fiber to the Home
