ISL43140IRZ
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | QFN |
| Packaging | Bulk |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 16 |
| Resistance | 65Ohm |
| Terminal Finish | MATTE TIN |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 16 |
| JESD-30 Code | S-PQCC-N16 |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 50nA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 70 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| Dual Supply Voltage | 5V |
| On-state Resistance Match-Nom | 2Ohm |
| Switch-on Time-Max | 80ns |
| Switch-off Time-Max | 30ns |
| Normal Position | NC |
| Height Seated (Max) | 1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
ISL43140IRZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in QFN. High reliability is provided by advanced packaging method Bulk. The total number of terminations is 16. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. It is injected into the electrical part body with 16 pins. It has an internal resistance of 65Ohm. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 2V as the lowest voltage for the electrical part. For this multiplexer to operate, 50nA current would be sufficient. It may damage the digital multiplexer if the voltage is higher than 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 6VFor dual power supplies, a voltage of at least 2V should be attached. The switches should not operate in an environment where the temperature is higher than 85°C. It can conduct in a 4-bit manner.
ISL43140IRZ Features
1 Channels
50nA Supply Current
4-Bit
ISL43140IRZ Applications
There are a lot of Intersil (Renesas Electronics America) ISL43140IRZ Analog Switches & Multiplexers ICs applications.
- Communication systems
- E1 Multiplexer
- Industrial control systems
- Precision instrumentation
- Fault Tolerant Systems
- Low-Voltage
- Transmit
- T1/E1 Terminals
- Sample hold systems
- PBX interfaces
