ISL43140IRZ-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | QFN |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 16 |
| Resistance | 65Ohm |
| Terminal Finish | MATTE TIN |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 16 |
| JESD-30 Code | S-PQCC-N16 |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 50nA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 70 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| Dual Supply Voltage | 5V |
| On-state Resistance Match-Nom | 2Ohm |
| Switch-on Time-Max | 80ns |
| Switch-off Time-Max | 30ns |
| Normal Position | NC |
| Height Seated (Max) | 1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
ISL43140IRZ-T Overview
Due to its QFN packaging, the electronic part is convenient for international shipping. The total number of terminations is 16. High-quality output is provided by the electronic component's 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 16 pins. A 65Ohm internal resistance characterizes this multiplexer. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 2V voltage fed to the electrical part below 2V. In order to operate this switch device, it would need a current of 50nA. Put voltage above 1μA on the multiplexer to cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 6VYou should attach at least 2V voltage if you are using dual power supply. The switches should not operate in an environment where the temperature is higher than 85°C. It can conduct in a 4-bit manner.
ISL43140IRZ-T Features
1 Channels
50nA Supply Current
4-Bit
ISL43140IRZ-T Applications
There are a lot of Intersil (Renesas Electronics America) ISL43140IRZ-T Analog Switches & Multiplexers ICs applications.
- HDTV
- Residential Gateways, Home Gateway/Router
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- PBX interfaces
- ATM
- Optical Applications
- Avionics and Military Systems
- High speed data transmission line cards
- Digital cross connects (DSX-1)
- Precision instrumentation
