ISL43141IRZ-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | QFN |
| Packaging | Tape & Reel |
| Published | 2001 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 16 |
| Resistance | 65Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 16, 16, 16 |
| JESD-30 Code | S-PQCC-N16 |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 50nA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 70 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| Dual Supply Voltage | 5V |
| On-state Resistance Match-Nom | 2Ohm |
| Switch-on Time-Max | 80ns |
| Switch-off Time-Max | 30ns |
| Normal Position | NO |
| Height Seated (Max) | 1mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
ISL43141IRZ-T Overview
The electrical component comes in QFN packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Total terminations are 16. This electronic part offers high-quality output due to its 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. As part of the design of the 16, 16, 16 series, this electronic part has been incorporated into the system. It has an internal resistance of 65Ohm. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. Analogue multiplexers of the Dual, Single supply type that are cost-effective. A low voltage of 2V should be applied to the electronic component. 50nA current would be enough for this multiplexer to operate. The analogue multiplexer may be damaged if voltage is greater than 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 6VFor dual power supplies, a voltage of at least 2V should be attached. Temperatures over 85°C should not be allowed for the multiplexer to operate. It conducts in a 4-bit manner.
ISL43141IRZ-T Features
1 Channels
50nA Supply Current
4-Bit
ISL43141IRZ-T Applications
There are a lot of Intersil (Renesas Electronics America) ISL43141IRZ-T Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- Communication systems
- Cross Connects
- Communications systems
- SDH/SONET multiplexers
- Isolation
- Fiber In The Loop (FITL)
- ISDN NT1/TA
- Avionics and Military Systems
- Audio signal routing
