ISL43141IVZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 16 |
| Packaging | Bulk |
| Published | 2001 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Resistance | 65Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 50nA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 70 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| Dual Supply Voltage | 5V |
| On-state Resistance Match-Nom | 2Ohm |
| Switch-on Time-Max | 80ns |
| Switch-off Time-Max | 30ns |
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
ISL43141IVZ Overview
Shipping overseas is convenient with the electronic component packed in TSSOP. In order to provide high reliability, an advanced packaging method Bulk is used. 16 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. An switch multiplexer with 65Ohm internal resistance has a value of 65Ohm. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 2V voltage fed to the electrical part below 2V. This multiplexer would work with 50nA current. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 6V. It is recommended that you attach at least 2V to your dual power supply. Temperatures above 85°C degrees Celsius should not be operated by the multiplexer. It can conduct 4-bit signals.
ISL43141IVZ Features
1 Channels
50nA Supply Current
4-Bit
ISL43141IVZ Applications
There are a lot of Intersil (Renesas Electronics America) ISL43141IVZ Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Medical
- Fiber to the Home
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Multiplexers
- Industrial and process control systems
- Ultrasound
- Remote wireless modules
- Multi-Line E1 Interface Cards
- Video signal routing
