ISL8393IBZ
| Parameters | |
|---|---|
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 10nA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| Dual Supply Voltage | 5V |
| Off-state Isolation-Nom | 71 dB |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Packaging | Bulk |
| Published | 2001 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
ISL8393IBZ Overview
This electronic part is conveniently packaged in SOIC, making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Bulk is used. In total, 16 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. The electronic part body is injected with 16 pins. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. The analogue multiplexer could operate on 10nA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Despite this switch's dual supply capability, its voltage should not exceed 6V. With dual power supplies, you should attach at least 2V. This analog switch ic utilizes SEPARATE OUTPUT output. The switches should not operate in an environment where the temperature is higher than 85°C. It can conduct in a 4-bit manner.
ISL8393IBZ Features
1 Channels
10nA Supply Current
4-Bit
ISL8393IBZ Applications
There are a lot of Intersil (Renesas Electronics America) ISL8393IBZ Analog Switches & Multiplexers ICs applications.
- Isolation
- Battery Powered Systems
- DSLAMs
- Medical
- Routers
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Sample-and-hold systems
- SONET
- New designs requiring multiplexer functions
- Voice over IP/DSL – Integrated Access Devices, Smart
