ISL8394IBZ
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Packaging | Bulk |
| Published | 2001 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 20 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | QUAD 2:1 MUX OR DUAL 2-CHANNEL DMUX; ALSO OPERATE WITH 2V TO12V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| JESD-30 Code | R-PDSO-G20 |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 10nA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPDT |
| Turn On Delay Time | 130 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| Dual Supply Voltage | 5V |
| Off-state Isolation-Nom | 71 dB |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
ISL8394IBZ Overview
Presented in SOIC, this electrical component is convenient for overseas shipping. Advanced packaging method Bulk is used to provide high reliability. The total number of terminations is 20. By its 1 channels, the electronic component provides high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. The electronic part body is injected with 20 pins. There is 35Ohm internal resistance in this digital multiplexer. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 2V. It would be sufficient to run this analogue multiplexer with 10nA current. The analogue multiplexer may be damaged if voltage is greater than 1μA. There is no problem with using dual supply voltage, but it should not exceed 6V. For dual power supplies, a voltage of at least 2V should be attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. This electronic part has additional features, such as: QUAD 2:1 MUX OR DUAL 2-CHANNEL DMUX; ALSO OPERATE WITH 2V TO12V SINGLE SUPPLY. The switches should not operate in an environment where the temperature is higher than 85°C. It is capable of carrying out 4-bit operation.
ISL8394IBZ Features
1 Channels
10nA Supply Current
Additional Features: QUAD 2:1 MUX OR DUAL 2-CHANNEL DMUX; ALSO OPERATE WITH 2V TO12V SINGLE SUPPLY
4-Bit
ISL8394IBZ Applications
There are a lot of Intersil (Renesas Electronics America) ISL8394IBZ Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- ISDN NT1/TA
- Cell phones
- Communication systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- PDAs
- Fault Tolerant Systems
- T1/E1 Terminals
- Switching Systems
- HDTV
