ISL84051IAZ
| Parameters | |
|---|---|
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100nA |
| Throw Configuration | DPST |
| Propagation Delay | 75 ns |
| Turn On Delay Time | 180 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| Off-state Isolation-Nom | 90 dB |
| On-state Resistance Match-Nom | 6Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Switch-off Time-Max | 50ns |
| Length | 4.89mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 16 |
| Packaging | Bulk |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 225Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
ISL84051IAZ Overview
Due to its SSOP packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Bulk. A total of 16 terminations have been recorded. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. An switch multiplexer with 225Ohm internal resistance has a value of 225Ohm. For functions related to 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 2V should be the lowest voltage fed to the electronic component. An operating current of 1μA would be sufficient for this switch device. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. The voltage should be at least 2V if you are using dual power supplies. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. 9V operating voltages can be used with this electrical part. Additional features of the electronic component include: VIDEO APPLICATION. A temperature above 85°C is not suitable for operation of the analogue multiplexer.
ISL84051IAZ Features
1 Channels
1μA Supply Current
Additional Features: VIDEO APPLICATION
ISL84051IAZ Applications
There are a lot of Intersil (Renesas Electronics America) ISL84051IAZ Analog Switches & Multiplexers ICs applications.
- DSUs
- Video signal routing
- Precision test equipment
- Digital access cross connects
- 65 V DACs
- Audio signal routing
- Audio and video switching
- Communication systems
- PDH Multiplexers
- Access Concentrators
