ISL84052IBZ-T7A
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Packaging | Tape & Reel |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| Resistance | 225Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | VIDEO APPLICATION |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 9V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Propagation Delay | 75 ns |
| Turn On Delay Time | 180 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| Off-state Isolation-Nom | 90 dB |
| On-state Resistance Match-Nom | 6Ohm |
| Switch-on Time-Max | 60ns |
| Switch-off Time-Max | 50ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
ISL84052IBZ-T7A Overview
Presented in SOIC, this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel. Total terminations are 16. A 4 channel electronic part produces high-quality output. A 5V voltage supply should turn on and run the electronic component. It has an internal resistance of 225Ohm. Datasheets for 16 pin functions are available upon request. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. 1μA current would be enough for this multiplexer to operate. A voltage higher than 1μA may cause damage to the switch multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. When using dual power supplies, you should attach at least 2V. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. A voltage of 9V can be used to operate the electronic component. Check out the electrical component's additional features, such as the following: VIDEO APPLICATION. A temperature above 85°C is not suitable for operation of the analogue multiplexer.
ISL84052IBZ-T7A Features
4 Channels
1μA Supply Current
Additional Features: VIDEO APPLICATION
ISL84052IBZ-T7A Applications
There are a lot of Intersil (Renesas Electronics America) ISL84052IBZ-T7A Analog Switches & Multiplexers ICs applications.
- High-Voltage
- E1 Network Equipment
- Intelligent PBX
- High speed data transmission line cards
- Digital access cross connects
- Avionics test equipment
- Fiber In The Loop (FITL)
- Isolation
- USB 1.1 signal switching circuits
- HDTV
