ISL84053IBZ-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 225Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 16, 16, 16 |
| JESD-30 Code | R-PDSO-G16 |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Number of Bits | 3 |
| Throw Configuration | SPDT |
| Turn On Delay Time | 50 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 40 ns |
| Max Dual Supply Voltage | 6V |
| Min Dual Supply Voltage | 2V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 5V |
| Low Level Output Current | 30mA |
| Off-state Isolation-Nom | 90 dB |
| On-state Resistance Match-Nom | 6Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
ISL84053IBZ-T Overview
Packed in SOIC, the electronic component is convenient for shipping overseas. In total, 16 terminations have occurred. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. The electrical component body receives 16, 16, 16 pins. As far as internal resistance is concerned, it has 225Ohm. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 12V. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 2V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 1μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 2V voltage attached. Check out the electrical component's additional features, such as the following: VIDEO APPLICATION. Temperatures over 85°C should not be allowed for the multiplexer to operate. 3-bit operation is possible.
ISL84053IBZ-T Features
1 Channels
1μA Supply Current
Additional Features: VIDEO APPLICATION
3-Bit
ISL84053IBZ-T Applications
There are a lot of Intersil (Renesas Electronics America) ISL84053IBZ-T Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- Cable Modem
- Audio signal routing
- PBX interfaces
- Communication systems
- Public switching systems
- Automatic test equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Residential Gateways, Home Gateway/Router
- Frame Relay Equipment
