banner_page

ISL84517IHZ-T

Analog Switches BREAK-BEFORE-MAKE 5 Pins 5V SOT-23-5


  • Manufacturer: Intersil (Renesas Electronics America)
  • Nocochips NO: 391-ISL84517IHZ-T
  • Package: SOT-23-5
  • Datasheet: PDF
  • Stock: 625
  • Description: Analog Switches BREAK-BEFORE-MAKE 5 Pins 5V SOT-23-5(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Contact Plating Tin
Mount Surface Mount
Package / Case SOT-23-5
Number of Pins 5
Packaging Tape & Reel
Published 2001
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 3
Number of Terminations 5
Resistance 20Ohm
Max Operating Temperature 85°C
Min Operating Temperature -40°C
Subcategory Multiplexer or Switches
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 5V
Time@Peak Reflow Temperature-Max (s) 40
Pin Count 5
Operating Supply Voltage 5V
Polarity Non-Inverting
Temperature Grade INDUSTRIAL
Number of Channels 1
Max Supply Voltage 6V
Operating Supply Current 40μA
Nominal Supply Current 40μA
Max Supply Current 125μA
Number of Bits 1
Throw Configuration SPST
Turn On Delay Time 100 ns
Supply Type Dual
Bandwidth 400MHz
Neg Supply Voltage-Nom (Vsup) -5V
Turn-Off Delay Time 75 ns
Max Dual Supply Voltage 6V
Min Dual Supply Voltage 1.5V
High Level Output Current 20mA
Dual Supply Voltage 5V
Switching BREAK-BEFORE-MAKE
Normal Position NC
Length 2.9mm
Radiation Hardening No
RoHS Status RoHS Compliant
Lead Free Lead Free

ISL84517IHZ-T Overview


As the electronic part is packed in SOT-23-5, international shipping is convenient. High reliability is ensured by the advanced packaging method Tape & Reel. In total, 5 terminations have occurred. A 1 channel electronic part produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 5 series. It has an internal resistance of 20Ohm. Datasheets for 5 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. Analogue multiplexer with a Dual supply type that is cost-effective. The analogue multiplexer could operate on 40μA current. When the digital multiplexer is charged above 125μA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. With dual power supplies, you should attach at least 1.5V. Operating voltages range from 5V. 400MHz-bandwidths can be used to transfer data between multiplexers. Temperatures over 85°C should not be allowed for the multiplexer to operate. Its conductivity is 1-bit.

ISL84517IHZ-T Features


1 Channels
40μA Supply Current
Bandwidth: 400MHz
1-Bit

ISL84517IHZ-T Applications


There are a lot of Intersil (Renesas Electronics America) ISL84517IHZ-T Analog Switches & Multiplexers ICs applications.

  • Medical Instrumentation
  • Relay replacements
  • Ultrasound
  • Communications systems
  • Existing multiplexer applications (both fault-protected and nonfault-protected)
  • FTTH
  • SDH
  • 65 V DACs
  • Cable Telephony – NIU, Set-Top Box, Home Side Box
  • Industrial

Write a review

Note: HTML is not translated!
    Bad           Good