ITS428L2ATMA1
| Parameters | |
|---|---|
| Output Peak Current Limit-Nom | 1.8A |
| Rds On (Typ) | 50m Ω |
| Turn Off Time | 200 µs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 2.5mm |
| Length | 6.5mm |
| Width | 6.22mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-5, DPak (4 Leads + Tab), TO-252AD |
| Surface Mount | YES |
| Operating Temperature | -30°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | PROFET® |
| JESD-609 Code | e3 |
| Feature | Status Flag |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ITS428L2 |
| Pin Count | 4 |
| JESD-30 Code | R-PSSO-G4 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Supply Voltage-Max (Vsup) | 43V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Interface | On/Off |
| Current - Output (Max) | 5.8A |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.75V~43V |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
| Turn On Time | 200 µs |
ITS428L2ATMA1 Overview
Tape & Reel (TR) is how it's packaged.The TO-252-5, DPak (4 Leads + Tab), TO-252AD package contains it.Surface Mount is the mounting type of the LED driver.There is a General Purpose switch type associated with it.Ensure reliable operation by setting the temperature to -30°C~85°C TA.The LED driver is equipped with 1 outputs.A voltage of Not Required is used to power it.The maximum output voltage of this LED driver is N-Channel volts.It is equipped with Status Flag features.It comes under the family of ITS428L2.There are 4 terminations in it.Currently, the lighting driver has a total of 1 functions.In this case, the LED driving board can produce only 5.8AV as its maximum output.Supply voltages of 5V allow for high efficiency.It is equipped with a total of 4 pins.Electrical components such as this are included in the PROFET? series.The maximum supply voltage for this lighting driver is set to 43V (Vsup).In order for the lighting driver to operate normally, the supply voltage (Vsup) should be maintained above 4.75V.
ITS428L2ATMA1 Features
Supplied from 5V
ITS428L2ATMA1 Applications
There are a lot of Infineon Technologies ITS428L2ATMA1 Power Switches ICs applications.
- Hot Swap
- Hot Swap
- Solid-State Drives
- Storage Drives
- Set-top-box
- Wireless Modem Data Cards
- Notebook and Tablet Computers
- Telecom and Network Systems
- USB Power Distribution
- PC Card Hot Swap
