KA2904DTF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | LIFETIME (Last Updated: 20 hours ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 230.4mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Last Time Buy |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | KA2904 |
| Operating Supply Voltage | 26V |
| Number of Elements | 2 |
| Operating Supply Current | 800μA |
| Nominal Supply Current | 1.2mA |
| Output Current | 30mA |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 45nA |
| Voltage - Supply, Single/Dual (±) | 3V~26V ±1.5V~13V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 7mV |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2.9mV |
| Width | 3.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
KA2904DTF Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. The instrumentation amplifier in this picture is of the General Purpose-type. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 8. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. It should be noted that this op amp is a type of Operational Amplifier device. A total of 8 pins are present on the instrumentation amplifier. The input offset voltage is 7mV. This electrical part should be mounted using type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . You can run this op amp ic on 800μA . The voltage gain should stay at 100dB. There is a rating of 2 for the operating supply voltage of the buffer op amp. The operating supply voltage of the buffer op amp is rated at 26V. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
KA2904DTF Features
supply voltage of 5V
100dB voltage gain
KA2904DTF Applications
There are a lot of ON Semiconductor KA2904DTF Instrumentational OP Amps applications.
- Signal operation
- Large motor controllers
- Subtraction operation circuits
- Addition operation circuits
- Differentiator circuits
- Band-stop filter
- Inverse/same-phase proportional circuit
- Signal filtering
- Vehicle electronics
- Automation control systems
