L6205D
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | -25°C~125°C TJ |
| Packaging | Tube |
| Series | STSPIN L62 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Applications | General Purpose |
| Subcategory | Motion Control Electronics |
| Technology | BiCDMOS |
| Voltage - Supply | 8V~52V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 48V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | L6205 |
| Function | Driver - Fully Integrated, Control and Power Stage |
| Number of Outputs | 4 |
| Output Voltage | 52V |
| Max Output Current | 5.6A |
| Operating Supply Voltage | 48V |
| Supply Voltage-Min (Vsup) | 8V |
| Number of Channels | 2 |
| Interface | Parallel |
| Analog IC - Other Type | STEPPER MOTOR CONTROLLER |
| Operating Supply Current | 10mA |
| Output Configuration | Half Bridge (4) |
| Output Current per Channel | 2.8A |
| Collector Emitter Voltage (VCEO) | 52V |
| Max Collector Current | 2.8A |
| Voltage - Load | 8V~52V |
| Switching Frequency | 100kHz |
| Motor Type | Brushed |
| Motor Type - AC, DC | Brushed DC |
| Motor Type - Stepper | Bipolar |
| Height | 2.35mm |
| Length | 13mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
L6205D Overview
Drivers controllers is designed with Tube package.The part is packged with 20-SOIC (0.295, 7.50mm Width) case.Ideally, the part should be mounted by Surface Mount.As a result, it is appropriate for the component connected to General Purpose.8V~52V volts can be supplied by the device.Regarding the operating temperature, it is in the range of -25°C~125°C TJ°C.Drivers controllers is possible to categorize the motor type as Brushed DC.This part has 20termination options.At a rate of [0], voltage can be applied to the load.You should run this amplifier at 48V.A Surface Mountmounting method is recommended for this product.A STEPPER MOTOR CONTROLLERanalog IC is employed in this device.Drivers controllers is based on the L6205 part number.This device is designed with a pin count of 20.Drivers controllers is a part of the Motion Control Electronics series.Drivers controllers is possible to access 4outputs.A supply voltage of 48V is required for the operation of this driver.At [0], the output voltage is maintained.Drivers controllers is maintained at a voltage of STSPIN L62.A motor type of Brushedcan be recognized.The maximum output current reaches 5.6Ato meet the operating requirements.The supply current used for its operating is 10mA.On it, there are 2 channels.
L6205D Features
Applications : General Purpose
Load voltage across the chip 8V~52V
base on L6205 number
designed with 4 outputs
Motor Type classified as Brushed
L6205D Applications
There are a lot of STMicroelectronics L6205D motor drivers applications.
- Commercial office
- Charge pump circuits
- High power LED street light
- Emergency lighting
- Outdoor area lights
- Hospitality buildings
- Camcorders
- Lighting for health and wellbeing
- Fog lamps
- Digital still cameras
