Parameters |
Lifecycle Status |
LIFETIME (Last Updated: 1 week ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Number of Pins |
8 |
Operating Temperature |
-20°C~90°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2013 |
JESD-609 Code |
e6 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Terminal Finish |
Tin/Bismuth (Sn/Bi) |
Applications |
DC Motors, General Purpose |
Subcategory |
Motion Control Electronics |
Technology |
Bipolar |
Voltage - Supply |
2.5V~16V |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
1 |
Supply Voltage |
12V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
LA6581 |
Pin Count |
8 |
Number of Outputs |
1 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
16V |
Supply Voltage-Min (Vsup) |
2.5V |
Interface |
Logic |
Analog IC - Other Type |
BRUSHLESS DC MOTOR CONTROLLER |
Nominal Supply Current |
19mA |
Output Configuration |
Half Bridge (2) |
Power Dissipation |
400mW |
Output Current |
300mA |
Halogen Free |
Halogen Free |
Voltage - Load |
2.5V~16V |
Fault Protection |
Over Temperature |
Load Type |
Inductive |
Length |
3mm |
Width |
3mm |
RoHS Status |
RoHS Compliant |
Lead Free |
Lead Free |
LA6581T-TE-L-H Overview
H bridge is packaged using Tape & Reel (TR).As a cost-saving measure, H bridge is included in the 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) package.In addbridge driverion, 2.5V~16V can be used to improve reliabilbridge drivery.There is a mounting of H bridge circuit in Surface Mount.As long as -20°C~90°C TA operates at the right temperature, motor driver H bridge will operate normally.Among H bridge motor drivers many uses, H bridge motor driver can be found in DC Motors, General Purpose as well.Mount the board using Surface Mount.Transmission lines are terminated with 8 terminations with the H bridge that matches their characteristic impedance.It is used as a pronged contact as H bridge ic of a signal interface when 8 pins are used.Based on its base H bridge ic number of LA6581, more closely related H bridge ics can be found.There is a voltage supply of 12V that is used to operate H bridge circuit.This H bridge circuit incorporates an analog IC with the type BRUSHLESS DC MOTOR CONTROLLER.The output pins and the power supply pins are conducting 300mA current.It is the 8 pins that enable this bridge driver to perform its specific functions.The Hbridge is equipped with 1 outputs.H bridge motor drivers in the subcategory Motion Control Electronics have a wide range of similarities.The operating supply voltage is maintained at 16V in order to ensure high efficiency.
LA6581T-TE-L-H Features
Available in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : LA6581
Number of Receivers: 16V
LA6581T-TE-L-H Applications
There are a lot of ON Semiconductor LA6581T-TE-L-H Full Bridge Drivers, Half-Bridge Drivers applications.
- High-Current DC-DC Point-of-Load Converters
- DC-DC Converters
- Telecom Microprocessor
- High-Performance Gaming Motherboards
- Voltage Regulators for CPUs
- Non-V-Core
- High current, low profile DC-DC converters
- Industrial Fans
- V-Core
- Home Appliances