LA6595T-TLM-E
| Parameters | |
|---|---|
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 1 month ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -30°C~90°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e6 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Terminal Finish | Tin/Bismuth (Sn/Bi) |
| Applications | DC Motors, General Purpose |
| Subcategory | Motion Control Electronics |
| Technology | Bipolar |
| Voltage - Supply | 2.2V~14V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Terminal Pitch | 0.65mm |
| Base Part Number | LA6595 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Supply Voltage-Min (Vsup) | 2.2V |
| Interface | Logic |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 9mA |
| Output Configuration | Half Bridge (2) |
| Power Dissipation | 400mW |
| Output Current | 500mA |
| Collector Emitter Voltage (VCEO) | 14V |
| Max Collector Current | 500mA |
| Voltage - Load | 2.2V~14V |
| Fault Protection | Over Temperature |
| Motor Type | Brushless DC (BLDC) |
| Load Type | Inductive |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
LA6595T-TLM-E Overview
In order to package H bridge, Tape & Reel (TR) is used.A cost-saving measure, H bridge is included in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width).Improved reliabilbridge drivery can be ensured based on the supply voltage of 2.2V~14V.H bridge circuit is mounted on Surface Mount.The operating temperature of -30°C~90°C TA enables motor driver H bridge to work normally.Among H bridge motor drivers many applications are DC Motors, General Purpose.Mount the board using Surface Mount.Transmission lines can be terminated with a termination that matches the characteristic impedance of the line using 8 terminations.8 pins is used as pronged contacts as H bridge ic of a signal interface.The base H bridge ic number of LA6595 can be used to find related H bridge ics.A voltage of 12V is used as the supply voltage.As its analog IC type, H bridge circuit has been incorporated with BRUSH DC MOTOR CONTROLLER.A current of 500mA flows through the pins of the output and power supply.It is the 8 pins that enable this bridge driver to perform its specific functions.The Hbridge is equipped with 1 outputs.H bridge motor drivers in the subcategory Motion Control Electronics have a wide range of similarities.
LA6595T-TLM-E Features
Available in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : LA6595
LA6595T-TLM-E Applications
There are a lot of ON Semiconductor LA6595T-TLM-E Full Bridge Drivers, Half-Bridge Drivers applications.
- Non-V-Core
- PC peripherals
- OA equipments
- Voltage Regulators for DDR memory arrays
- Networking Microprocessor Voltage Regulators
- Industrial Automation
- Compact Blade Servers
- Notebook Computers
- V-Core
- CD players
