LB11961-TLM-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-LSSOP (0.173, 4.40mm Width) + 2 Heat Tabs |
| Number of Pins | 14 |
| Operating Temperature | -30°C~90°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e6 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| Terminal Finish | Tin/Bismuth (Sn/Bi) |
| Applications | Fan Motor Driver |
| HTS Code | 8542.39.00.01 |
| Subcategory | Motion Control Electronics |
| Technology | Bipolar |
| Voltage - Supply | 4.5V~16V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 12V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Function | Driver - Fully Integrated, Control and Power Stage |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 14V |
| Supply Voltage-Max (Vsup) | 16V |
| Power Supplies | 12V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Interface | Parallel |
| Analog IC - Other Type | BRUSHLESS DC MOTOR CONTROLLER |
| Nominal Supply Current | 24mA |
| Output Configuration | Half Bridge (2) |
| Power Dissipation | 1.1W |
| Current - Output | 1A |
| Logic Function | AND |
| Voltage - Load | 4.5V~16V |
| Motor Type - AC, DC | Brushed DC |
| Height Seated (Max) | 1.5mm |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LB11961-TLM-E Overview
Drivers controllers includes a Tape & Reel (TR)package.Drivers controllers comes in a 14-LSSOP (0.173, 4.40mm Width) + 2 Heat Tabs case.Drivers controllers is recommended that the part be mounted by Surface Mount.Fits the component connected to Fan Motor Driver.In this case, the device can supply 4.5V~16V volts.With regard to operating temperature, it ranges -30°C~90°C TA. A motor of this type can be categorized as Brushed DC.The part has 14terminations available.In this case, the voltage can be applied to the load at the rate of 4.5V~16V.Please take in mind that this amplifier should be run at 12V.In terms of mounting, it is recommended that it be mounted in Surface Mount.Maintain a current of 1Afor the part output.There is an analog integrated circuit BRUSHLESS DC MOTOR CONTROLLERpresent in the device.14pins are available on the device.This is part of the Motion Control Electronics series.A voltage of 14V is used as the supply voltage for this driver.
LB11961-TLM-E Features
Applications : Fan Motor Driver
Load voltage across the chip 4.5V~16V
LB11961-TLM-E Applications
There are a lot of ON Semiconductor LB11961-TLM-E motor drivers applications.
- Outdoor area lights
- Tunnel lights
- RGB and monochromatic LED drivers for signage and traffic signals
- Automotive exterior and interior lighting
- Alternative to HID lights
- Dome
- Smart lighting applications
- Lighting for the ambience of tunability
- Dash
- Camera-enabled smartphones
