LB1933M-TRM-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 3 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-LSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -30°C~75°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e6 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| Terminal Finish | Tin/Bismuth (Sn/Bi) |
| Applications | DC Motors, General Purpose, Stepper Motors |
| HTS Code | 8542.39.00.01 |
| Subcategory | Motion Control Electronics |
| Technology | Bipolar |
| Voltage - Supply | 2.2V~7.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 1mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 7.5V |
| Power Supplies | 3V |
| Supply Voltage-Min (Vsup) | 1.8V |
| Interface | Logic |
| Analog IC - Other Type | STEPPER MOTOR CONTROLLER |
| Nominal Supply Current | 10μA |
| Output Configuration | Half Bridge (4) |
| Power Dissipation | 550mW |
| Output Current | 1A |
| Output Current per Channel | 1A |
| Supply Current-Max (Isup) | 25mA |
| Voltage - Load | 1.8V~7.5V |
| Fault Protection | Over Temperature |
| Load Type | Inductive |
| Height Seated (Max) | 1.7mm |
| Length | 8mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
LB1933M-TRM-E Overview
Tape & Reel (TR) is used to package H bridge.In an effort to save money, H bridge is included in the 14-LSOP (0.173, 4.40mm Width) package.Based on 2.2V~7.5V, improved reliabilbridge drivery can be achieved.H bridge circuit is mounted in the way of Surface Mount.A normal operation of -30°C~75°C TA is enabled by motor driver H bridges operating temperature.Among H bridge motor drivers many uses, H bridge motor driver can be found in DC Motors, General Purpose, Stepper Motors as well.Surface Mount is adopted as a technique to mount H gate on the PCB.A transmission line is terminated with a H bridge that matches its characteristic impedance, referred to as a 14 termination.An interface using 14 pins is used to provide pronged contact.A voltage of 3V is used as the supply voltage.STEPPER MOTOR CONTROLLER has been incorporated as H bridge circuit's analog IC type.Output and power supply pins have a current of 1A.It is through the 14 pins that the bridge driver can perform its specific functions.H bridge motor drivers in the subcategory Motion Control Electronics have a wide range of similarities.In order to maintain a high level of efficiency, the operating supply voltage is maintained at 7.5V.Electricity from 3V is supplied to the electrical load.
LB1933M-TRM-E Features
Available in 14-LSOP (0.173, 4.40mm Width) Package / Case
Operating Temperature at the range of Surface Mount
Number of Receivers: 7.5V
LB1933M-TRM-E Applications
There are a lot of ON Semiconductor LB1933M-TRM-E Full Bridge Drivers, Half-Bridge Drivers applications.
- PC peripherals
- Desktop Computers
- DC-DC Converters
- Home Appliances
- Notebook Computers
- Networking Microprocessor Voltage Regulators
- Voltage Regulators
- Compact Blade Servers
- OA equipments
- Industrial Fans
