Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
14-CDIP (0.300, 7.62mm) |
Number of Pins |
14 |
Operating Temperature |
-55°C~125°C |
Packaging |
Tube |
Series |
BI-FET II™ |
JESD-609 Code |
e0 |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Operational Amplifier |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Number of Functions |
4 |
Supply Voltage |
20V |
Base Part Number |
LF147 |
Pin Count |
14 |
Operating Supply Voltage |
22V |
Number of Elements |
4 |
Power Supplies |
+-15V |
Operating Supply Current |
7.2mA |
Nominal Supply Current |
7.2mA |
Power Dissipation |
900mW |
Output Current |
30mA |
Slew Rate |
13V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
J-FET |
Common Mode Rejection Ratio |
80 dB |
Current - Input Bias |
50pA |
Voltage - Supply, Single/Dual (±) |
5V~44V ±2.5V~22V |
Input Offset Voltage (Vos) |
5mV |
Gain Bandwidth Product |
4MHz |
Neg Supply Voltage-Nom (Vsup) |
-20V |
Unity Gain BW-Nom |
4000 kHz |
Voltage Gain |
100dB |
Average Bias Current-Max (IIB) |
0.05μA |
Power Supply Rejection Ratio (PSRR) |
80dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
1mV |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.0002μA |
Programmable Power |
NO |
Wideband |
NO |
Input Offset Current-Max (IIO) |
0.025μA |
Height |
5.08mm |
Length |
19.56mm |
Width |
6.67mm |
Thickness |
4.57mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
LF147J Overview
A 14-CDIP (0.300, 7.62mm) case is used to package the op amp. J-FET-type instrumentation amplifiers are used in this application. In the case of Tube cases, linear amplifier will be delivered. The number of terminations is approaching the 14 mark. Buffer amplifier has a total of 14 pins on it. As a reminder, this buffer op amp should be powered by 20V battery and that the battery should be inserted in the amplifier. This particular linear amplifier is a type of Operational Amplifier device, to be precise. An 14-pin op amp ic is included in the package. Op amp ic rates 5mV for input offset voltage. This electronic part is recommended for mounting type Through Hole. The buffer amplifier functions well at -55°C~125°C as far as operating temperature is concerned. Using a supply current of 7.2mA , this buffer op amp will be able to operate. It is recommended to keep the voltage gain at 100dB at all times. 4 elements make up the design of this buffer amplifier. The operating supply voltage of instrumentation amplifier is rated 22V voltage. BI-FET II? corresponds to linear amplifier's series.
LF147J Features
14 Pins
supply voltage of 20V
100dB voltage gain
LF147J Applications
There are a lot of Texas Instruments LF147J Instrumentational OP Amps applications.
- PDA
- Integrator circuits
- Navigation
- High/low-pass filter circuit
- High-frequency data acquisition systems
- Tablets
- Portable docking station
- Blood pressure sensors
- Switching amplifier
- Division circuits