LF351DT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LF351 |
| Pin Count | 8 |
| Number of Elements | 1 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 3.4mA |
| Output Current | 60mA |
| Min Input Voltage | -12V |
| Slew Rate | 16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 20pA |
| Max Input Voltage | 15V |
| Voltage - Supply, Single/Dual (±) | 6V~32V ±3V~16V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Dual Supply Voltage | 15V |
| Input Offset Current-Max (IIO) | 0.004μA |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LF351DT Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. An op amp ic of the J-FET type. Linear amplifier is delivered in a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. The total number of pins on linear amplifier is 8. I would like to remind you that this buffer op amp should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are available on the instrumentation amplifier. Regarding input offset voltage, op amp rates 10mV. For this electrical component, Surface Mount is the recommended mounting type. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of 0°C~70°C . As long as the supply current of the chip does not exceed 1.4mA, this op amp ic can operate. 106.02dB should remain the voltage gain. There is an operating supply voltage rating of 1 for this operational amplifier, which is rated at the manufacturer. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
LF351DT Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
LF351DT Applications
There are a lot of STMicroelectronics LF351DT Instrumentational OP Amps applications.
- Thermocouples
- Semiconductor detectors
- Test equipment
- Car stereo
- Power control
- Ultrasound transducers
- Industrial control system
- Wireless base stations
- Signal transformation
- Medical instruments
