LF353D
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 500mW |
| Technology | JFET |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | LF353 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Voltage | 15V |
| Operating Supply Current | 3.6mA |
| Nominal Supply Current | 6.5mA |
| Power Dissipation | 500mW |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 50pA |
| Voltage - Supply, Single/Dual (±) | ±3.5V~18V |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 5mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Input Offset Current-Max (IIO) | 0.004μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LF353D Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the J-FET-type. In the case of Tube cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 8. In this case, there are 8 pins on the board. Please take in mind that this instrumentation amplifier should be run at 15V. Instrumentation amplifier is a part of Operational Amplifier. An 8-pin op amp ic is included in the package. In terms of the input offset voltage, instrumentation amplifier rates at 10mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of 0°C~70°C . A supply current of 3.6mA can be used to operate this linear amplifier. 100dB should be the voltage gain. The op amp ic has 2 channels on it.
LF353D Features
8 Pins
supply voltage of 15V
100dB voltage gain
LF353D Applications
There are a lot of Texas Instruments LF353D Instrumentational OP Amps applications.
- Hand-held batteries
- Fast A/D and D/A converters
- RF cable systems
- Commercial audio systems
- Differentiator circuits
- High input resistance broadband
- Proportional counter tubes
- Radiation thermometry transducers
- Signal transformation
- Power transmission
