LF353DT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LF353 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 3.2mA |
| Power Dissipation | 680mW |
| Output Current | 60mA |
| Min Input Voltage | 6V |
| Slew Rate | 16V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 20pA |
| Max Input Voltage | 36V |
| Voltage - Supply, Single/Dual (±) | ±3V~16V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.02dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Dual Supply Voltage | 15V |
| Input Offset Current-Max (IIO) | 0.004μA |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LF353DT Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. Buffer amps of this type are called J-FET-types. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. We are approaching the 8h termination of the year. In this case, there are 8 pins on the board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 8 pins are included on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 10mV. Surface Mount is the recommended mounting type for this linear amplifier. With regard to operating temperature, op amp ranges 0°C~70°C. A supply current of 1.4mA can be used to operate this linear amplifier. There should be no change in the voltage gain. Buffer op amp is equipped with 2 channels on the device. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted.
LF353DT Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
LF353DT Applications
There are a lot of STMicroelectronics LF353DT Instrumentational OP Amps applications.
- High/low-pass filter circuit
- Power control
- E-book readers
- Wireless base stations
- Radar
- single/dual op amp sum and difference circuits
- Cinema or auditorium audio system
- High-frequency data acquisition systems
- Multiplication circuits
- RF cable systems
