LF356N/NOPB
| Parameters | |
|---|---|
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 4.535924g |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | BI-FET™ |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 670mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | LF356 |
| Pin Count | 8 |
| Max Output Current | 25mA |
| Number of Channels | 1 |
| Operating Supply Current | 5mA |
| Nominal Supply Current | 5mA |
| Power Dissipation | 670mW |
| Output Current | 25mA |
| Slew Rate | 12V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | ±15V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 5MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Settling Time | 1.5 μs |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Input Offset Current-Max (IIO) | 0.00005μA |
| Max Junction Temperature (Tj) | 100°C |
| Ambient Temperature Range High | 70°C |
| Height | 5.08mm |
| Length | 9.81mm |
LF356N/NOPB Overview
The linear amplifier is packaged in a 8-DIP (0.300, 7.62mm) case. This is a J-FET type op amp. Upon delivery, op amp ic is packaged in a Tube case. The number of terminations approaches 8. A total of 8 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are included on the operational amplifiers. The input offset voltage is 3mV. For this electrical component, the recommended mounting type is Through Hole, which is the most common. With regard to operating temperature, op amp ranges 0°C~70°C. An 5mA volt supply current is needed for this linear amplifier to operate. The voltage gain should stay at 106.02dB. As far as the device is concerned, buffer amplifier has 1 channels. As the name implies, BI-FET? refers to the series of the buffer op amp.
LF356N/NOPB Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
LF356N/NOPB Applications
There are a lot of Texas Instruments LF356N/NOPB Instrumentational OP Amps applications.
- Commercial audio systems
- Medical imaging
- Multimedia playback equipment
- Automotive sensors
- Fast A/D and D/A converters
- Subtraction operation circuits
- single/dual op amp sum and difference circuits
- Exponential operation circuits
- Communication device
- Portable docking station
