LF412CDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Max Power Dissipation | 500mW |
| Technology | JFET |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | LF412 |
| Pin Count | 8 |
| Power Supplies | +-15V |
| Number of Channels | 2 |
| Operating Supply Current | 4.5mA |
| Nominal Supply Current | 4.5mA |
| Power Dissipation | 500mW |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 50pA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 800μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Input Offset Current-Max (IIO) | 0.0001μA |
| Ambient Temperature Range High | 70°C |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LF412CDR Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. There are two types of operational amplifiers in this circuit. The op amp is delivered to you in a Cut Tape (CT) case. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins on it. Please take in mind that this instrumentation amplifier should be run at 15V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. There are 8 pins on this chip. Regarding input offset voltage, buffer amplifier rates 1mV voltage. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about 0°C~70°C . Using a supply current of 4.5mA , this buffer op amp will be able to operate. It is recommended to keep the voltage gain at 106.02dB at all times. 2 channels are available on the instrumentation amplifier. It is used TR to pack the op amps.
LF412CDR Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
LF412CDR Applications
There are a lot of Texas Instruments LF412CDR Instrumentational OP Amps applications.
- Digital cameras
- High/low-pass filter circuit
- Communication
- Video conversion and routing
- Signal amplification
- Television broadcasting equipment
- Portable docking station
- Large motor controllers
- Mobile phone
- Semiconductor detectors
