banner_page

LF444CM/NOPB

4 Channels 10pA 70 dB Instrumentational OP Amps 0.00005μA 18V 10V~36V ±5V~18V LF444 14 Pins 14-SOIC (0.154, 3.90mm Width)


  • Manufacturer: Texas Instruments
  • Nocochips NO: 815-LF444CM/NOPB
  • Package: 14-SOIC (0.154, 3.90mm Width)
  • Datasheet: -
  • Stock: 163
  • Description: 4 Channels 10pA 70 dB Instrumentational OP Amps 0.00005μA 18V 10V~36V ±5V~18V LF444 14 Pins 14-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 2 days ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 14-SOIC (0.154, 3.90mm Width)
Number of Pins 14
Operating Temperature 0°C~70°C
Packaging Tube
Series BI-FET™
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Matte Tin (Sn)
Subcategory Operational Amplifier
Max Power Dissipation 670mW
Technology BIPOLAR
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 1.27mm
Base Part Number LF444
Pin Count 14
Operating Supply Voltage 18V
Power Supplies +-15V
Number of Channels 4
Operating Supply Current 600μA
Nominal Supply Current 600μA
Power Dissipation 670mW
Output Current 8mA
Max Supply Current 1mA
Slew Rate 1V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type J-FET
Common Mode Rejection Ratio 70 dB
Current - Input Bias 10pA
Voltage - Supply, Single/Dual (±) 10V~36V ±5V~18V
Input Offset Voltage (Vos) 3mV
Bandwidth 1MHz
Neg Supply Voltage-Nom (Vsup) -15V
Unity Gain BW-Nom 1000 kHz
Voltage Gain 100dB
Average Bias Current-Max (IIB) 0.00005μA
Power Supply Rejection Ratio (PSRR) 70dB
Low-Offset NO
Frequency Compensation YES
Low-Bias YES
Micropower YES
Bias Current-Max (IIB) @25C 0.0001μA
Programmable Power NO
Dual Supply Voltage 9V
Input Offset Current-Max (IIO) 0.00005μA
Height 1.75mm
Length 8.65mm
Width 3.91mm
Thickness 1.58mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant
Lead Free Lead Free

LF444CM/NOPB Overview


Packaged in a 14-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. J-FET-type instrumentation amplifiers are used in this application. Upon delivery, op amp ic is packaged in a Tube case. It is estimated that there will be 14 terminations in the next few months. A total of 14 pins are attached to buffer op amp. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. 14 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 3mV. The mounting type that is recommended for this electrical part is Surface Mount. It is important to note that this linear amplifier works well at a temperature of 0°C~70°C when it comes to operating temperatureAn 600μA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 100dB for the time being. 4 channels are available on the instrumentation amplifier. The operating supply voltage of the buffer op amp is rated at 18V. Buffer op amp series numbers are indicated by the BI-FET?.

LF444CM/NOPB Features


14 Pins
supply voltage of 15V
100dB voltage gain

LF444CM/NOPB Applications


There are a lot of Texas Instruments LF444CM/NOPB Instrumentational OP Amps applications.

  • Differentiator circuits
  • High/low-pass filter circuit
  • Oscilloscopes
  • Information processing
  • Video computer boards
  • Micro signal measurement
  • RF cable systems
  • Test and measurement instruments
  • Wireless base stations
  • Non-polarized electrodes

Write a review

Note: HTML is not translated!
    Bad           Good