LM10BH
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | TO-205AA, TO-5-8 Metal Can |
| Number of Pins | 8 |
| Operating Temperature | -25°C~85°C |
| Packaging | Bulk |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | BOTTOM |
| Terminal Form | WIRE |
| Number of Functions | 1 |
| Supply Voltage | 20V |
| Base Part Number | LM10 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Elements | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 1.1V |
| Operating Supply Current | 270μA |
| Nominal Supply Current | 400μA |
| Output Current | 20mA |
| Slew Rate | 0.2 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 93 dB |
| Current - Input Bias | 10nA |
| Input Offset Voltage (Vos) | 2mV |
| Gain Bandwidth Product | 90 kHz |
| Neg Supply Voltage-Nom (Vsup) | -20V |
| Voltage Gain | 112.04dB |
| Average Bias Current-Max (IIB) | 0.03μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 300μV |
| Max Dual Supply Voltage | 20V |
| Low-Bias | NO |
| Micropower | YES |
| Min Dual Supply Voltage | 550mV |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.0007μA |
| Height | 4.699mm |
| Length | 9.08mm |
| Width | 9.08mm |
| Thickness | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LM10BH Overview
The linear amplifier is packaged in a TO-205AA, TO-5-8 Metal Can case which makes it easy for the consumer to handle. Buffer amps of this type are called General Purpose-types. Upon delivery, op amp ic is packaged in a Bulk case. It is estimated that there will be 8 terminations in the next few months. In this case, there are 8 pins on the board. Please take in mind that this instrumentation amplifier should be run at 20V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 8-pin op amp ic is included in the package. As far as the input offset voltage is concerned, linear amplifier rates at 2mV. Through Hole is the recommended mounting type of operational amplifiers. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -25°C~85°C . A supply current of 270μA can be used to operate this linear amplifier. The voltage gain should stay at 112.04dB. This op amp ic has 1 circuits. There is a rating of 2 for the operating supply voltage of the buffer op amp. The operating supply voltage of instrumentation amplifier is rated 20V voltage. With regard tp supply voltage, op amp is used under 40V. A voltage of 1.1V or higher is recommended for the linear amplifier's supply voltage. Conduct linear amplifier under the dual suuply voltage of 20V.
LM10BH Features
8 Pins
supply voltage of 20V
112.04dB voltage gain
LM10BH Applications
There are a lot of Texas Instruments LM10BH Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Test equipment
- Portable docking station
- Power generator
- Industrial control system
- High speed sample
- Hand-held batteries
- Home audio systems
- Ultrasound transducers
- RF cable systems
