LM124DRG4
| Parameters | |
|---|---|
| Nominal Supply Current | 700μA |
| Output Current | 60mA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | 3V~32V ±1.5V~16V |
| Output Current per Channel | 60mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 1.2MHz |
| Unity Gain BW-Nom | 1200 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.3μA |
| Power Supply Rejection Ratio (PSRR) | 65dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 32V |
| Voltage - Input Offset | 3mV |
| Current - Output / Channel | 40mA |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.15μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Input Offset Current-Max (IIO) | 0.1μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | LM124 |
| Pin Count | 14 |
| Operating Supply Voltage | 16V |
| Power Supplies | +-1.5/+-16/3/32V |
| Number of Channels | 4 |
| Operating Supply Current | 1.4mA |
LM124DRG4 Overview
The linear amplifier is packaged in a 14-SOIC (0.154, 3.90mm Width) case. An op amp of this type is a General Purpose-type. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. We are approaching the 14h termination of the year. A total of 14 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 5V volts. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. There are 14 pins on this chip. Regarding input offset voltage, op amp rates 5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -55°C~125°C , which is a good operating temperature. You can run this op amp ic on 1.4mA . You should keep the voltage gain at 100dB for the time being. The op amp ic has 4 channels on it. The operating supply voltage of the buffer op amp is rated at 16V. To pack the operational amplifier ics, TR is adopted as the packing method.
LM124DRG4 Features
14 Pins
supply voltage of 5V
100dB voltage gain
LM124DRG4 Applications
There are a lot of Texas Instruments LM124DRG4 Instrumentational OP Amps applications.
- Voltage regulation circuit
- Fission chambers
- Laptop
- Strain gauges
- Addition operation circuits
- Video data acquisition
- Car stereo
- Signal filtering
- Industrial applications including automation
- Proportional operation circuits
