LM124DT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | LM124 |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Elements | 4 |
| Power Supplies | +-1.5/+-15/3/30V |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 40mA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | 3V~30V ±1.5V~15V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 1.3MHz |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.3μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 32V |
| Voltage - Input Offset | 2mV |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.15μA |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM124DT Overview
A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. Linear amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be 14 terminations in the next few months. A total of 14 pins are located on this board. Please take in mind that this instrumentation amplifier should be run at 5V. Instrumentation amplifier is a part of Operational Amplifier. The op amp ic has an array of 14 pins on it. As far as the input offset voltage is concerned, linear amplifier rates at 5mV. Surface Mount is the recommended mounting type for this linear amplifier. In relation to the operating temperature of this buffer op amp, it works well at an average of -55°C~125°C . The buffer amplifier is capable of operating from a supply current of 1.5mA . 100dB should be the voltage gain. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 4. The operating supply voltage of instrumentation amplifier is rated 15V voltage. This linear amplifier pack is based on the TAPE AND REEL axis.
LM124DT Features
14 Pins
supply voltage of 5V
100dB voltage gain
LM124DT Applications
There are a lot of STMicroelectronics LM124DT Instrumentational OP Amps applications.
- Power generator
- Comparator
- Differentiator circuits
- Ultrasound transducers
- Proportional counter tubes
- Digital cameras
- Hand-held batteries
- Home audio systems
- Scintillation detectors
- Automotive sensors
