LM201ADG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 4 days ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -25°C~85°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | RAIL |
| Max Power Dissipation | 625mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | LM201A |
| Pin Count | 8 |
| Power Supplies | +-5/+-20V |
| Number of Channels | 1 |
| Operating Supply Current | 1.8mA |
| Nominal Supply Current | 1.8mA |
| Power Dissipation | 625mW |
| Output Current | 30mA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30nA |
| Voltage - Supply, Single/Dual (±) | ±5V~22V |
| Halogen Free | Halogen Free |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 104.08dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | NO |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 700μV |
| Bias Current-Max (IIB) @25C | 0.075μA |
| Neg Supply Voltage-Max (Vsup) | -22V |
| Length | 4.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
LM201ADG Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. Op amps are General Purpose types of amplifier on the chip. A Tube case is used for delivering the op amp. There is a growing number of terminations approaching the number of 8. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 8-pin op amp ic is included in the package. There is an input offset voltage of 2mV for this buffer op amp. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -25°C~85°C for optimal performance. You can run this op amp ic on 1.8mA . Voltage gain should remain at 104.08dB. Buffer op amp is equipped with 1 channels on the device. As a result of this, the buffer amplifier is packed in RAIL.
LM201ADG Features
8 Pins
supply voltage of 15V
104.08dB voltage gain
LM201ADG Applications
There are a lot of ON Semiconductor LM201ADG Instrumentational OP Amps applications.
- Band-stop filter
- Test equipment
- Logarithmic operation circuits
- Wireless base stations
- Mobile phone
- Measurements of Wheatstone bridge
- Image computer boards
- Fast A/D and D/A converters
- Semiconductor detectors
- Medical instruments
