LM25088MHX-1/NOPB
| Parameters | |
|---|---|
| Package / Case | 16-PowerTSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 24V |
| Base Part Number | LM25088 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 40V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 42V |
| Input Voltage-Nom | 24V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 10A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~42V |
| Quiescent Current | 3.2mA |
| Control Features | Enable, Frequency Control, Ramp, Soft Start |
| Input Voltage (Min) | 4.5V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 50kHz~1MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Supply Current-Max (Isup) | 4.5mA |
| Synchronous Rectifier | No |
| Switcher Configuration | SINGLE |
| Max Frequency | 1MHz |
| Clock Sync | Yes |
| Duty Cycle | 97 % |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
LM25088MHX-1/NOPB Overview
In the 16-PowerTSSOP (0.173, 4.40mm Width) package, the switching controller meets most application requirements. dc motor controller is suitable for 1 output generation. Packaging for the pmic consists of Tape & Reel (TR) solid enclosures. Transistor Driver dc switching's outputs (s) can be handled by it. The supply and operating voltage of the dc control are 4.5V~42V. Work well in dc switchers with a -40°C~125°C TJ. Switching can be done at 50kHz~1MHz with this switching controller. A generalization of dc dc regulator can be made using Surface Mount. Enable, Frequency Control, Ramp, Soft Start is used for efficient switching control in the dcdc regulator. The switch converters are connected to a SWITCHING CONTROLLER analog IC. DUAL are the position of the terminal of the switching converters. A variety of 16 terminations are available in dc switching. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. The DC switcher's nominal voltage is 24V. Search for "LM25088" to find other relevant dc to dc converter ics. 16 pins are present on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. Input voltage of dc dc voltage regulator should be 4.5V. DC regulator outputs 40V voltage based on test statistics. If you start a project, note down the dc dc regulator's usual output current of 10A. Having a Surface Mount makes DC switcher ideal for most prototype and application designs. DC regulator has a maximum frequency of 1MHz. To operate the voltage regulator dc to dc safely and reliably, users should apply 42V. When the dc switching is dormant, it uses 3.2mA. Switching controller is necessary to supply a voltage of 24V. Current supplied to the controller should not exceed 4.5mA.
LM25088MHX-1/NOPB Features
Transistor Driver Outputs
Switching Frequency: 50kHz~1MHz
Enable, Frequency Control, Ramp, Soft Start
PULSE WIDTH MODULATION
LM25088MHX-1/NOPB Applications
There are a lot of Texas Instruments LM25088MHX-1/NOPB DC to DC converter applications.
- Planers
- Balance equipment
- Television equipment
- Industrial robots
- Fire elevators
- Remotely powered electric motors
- Constant current circuits
- Sink circuits
- Sensitive electronic devices
- Printing
