LM25116MHX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-PowerTSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Base Part Number | LM25116 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 36V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 42V |
| Input Voltage-Nom | 24V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 10A |
| Voltage - Supply (Vcc/Vdd) | 6V~42V |
| Quiescent Current | 4.6mA |
| Control Features | Enable, Frequency Control, Ramp, Soft Start |
| Input Voltage (Min) | 6V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 50kHz~1MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 590kHz |
| Max Duty Cycle | 85 % |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LM25116MHX Overview
Capsuled in the 20-PowerTSSOP (0.173, 4.40mm Width) package, the switching controller can be used for a wide range of applications. There is enough capacity in the dc motor controller to generate the output for the 1 input. Tape & Reel (TR) solid enclosure protects the pmic. With this function, you can deal with Transistor Driver dc switching's outputs (s). A 6V~42V voltage is supplied to the dc control and used for operating it. Workable in an dc switcher where -40°C~125°C TJ is the -40°C~125°C TJrm. There is a switch at 50kHz~1MHz that can be used with this controller. The Surface Mount value makes it suitable for general dc dc regulator. Enable, Frequency Control, Ramp, Soft Start provides dcdc regulator efficient switching control. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. The switching converters's terminals (s) are designed at DUAL. An array of 20 terminations of dc switching. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. DC switcher's input voltageis 24V volts. In addition to "LM25116", there are other relevant dc to dc converter ics you can find. There are only 20 pins on switching converter. There is a particular type of Switching Regulator or Controllers in switching converter. It is recommended that the input voltage of the dc dc voltage regulator be 6V. DC regulator outputs 36V voltage based on test statistics. normally, the dc dc regulator's output current is 10A, which you should keep in mind when starting a project. The maximum duty cycle of this voltage regulator dc to dc is set to 85 % to ensure reliability during power-up and power-down. DC switcher's Surface Mount qualifies it for most applications and prototypes. DC regulator has a maximum frequency of 590kHz. In order for the voltage regulator dc to dc to perform safely and reliably in a circuit, users are advised to apply 42V. Dormant dc switchings use 4.6mA.
LM25116MHX Features
Transistor Driver Outputs
Switching Frequency: 50kHz~1MHz
Enable, Frequency Control, Ramp, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 85 %
LM25116MHX Applications
There are a lot of Texas Instruments LM25116MHX DC to DC converter applications.
- Surge protection circuits
- Remotely powered electric motors
- Pipe bending machines
- USB circuits
- Ball screw pair
- Large fire protection systems
- Sink circuits
- Hydro power
- Thermal power
- Series voltage regulation circuits
