LM2727MTC
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 2MHz |
| Base Part Number | LM2727 |
| Function | Step-Down |
| Output Voltage | 600mV |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20A |
| Voltage - Supply (Vcc/Vdd) | 4.5V~5.5V |
| Quiescent Current | 1.5mA |
| Control Features | Current Limit, Enable, Frequency Control, Power Good, Soft Start |
| Max Output Voltage | 5V |
| Topology | Buck |
| Min Input Voltage | 4.5V |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 50kHz~2MHz |
| Max Input Voltage | 5.5V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Max Duty Cycle | 90 % |
| Clock Sync | No |
| Number of Output Phases | 1 |
| Height | 900μm |
| Length | 5mm |
| Width | 4.4mm |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LM2727MTC Overview
It comes in a 14-TSSOP (0.173, 4.40mm Width) package, so switching controller can be used for most applications. A solid enclosure of Tube surrounds pmic. There are Transistor Driver dc switching's output (s) that it can handle. The supply and operating voltage of the dc control are 4.5V~5.5V. Worked in an dc switcher with a -40°C~125°C TJ rating. The switching controller can be switched at 50kHz~2MHz. As it has a Surface Mount value, it can be used for general dc dc regulator. Switching control is made easier with the dcdc regulator's Current Limit, Enable, Frequency Control, Power Good, Soft Start. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. Terminal (s) of the switching converters are designed at the DUAL position. Various 14 terminations. These dc dc converter ics adapt several control methods, including PULSE WIDTH MODULATION. DC switcher's voltage input of 5V. A search for "LM2727" will reveal other relevant dc to dc converter ics. There are 14 pins on switching converter. In particular, switching converter is a type of Switching Regulator or Controllers. According to the test statistics, DC regulator outputs 600mV voltage. You should note down the dc dc regulator's usual output current of 20A when you start a project. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 90 %. DC switcher's Surface Mount makes it qualified for most application and prototype designs. DC switcher'sSwitching controllers work at 2MHz Hz. A dc switching in a dormant state uses 1.5mA. The maximum input voltage of dc switcher is 5.5V, so users should limit their voltage accordingly. The supply voltage must be 4.5V. Datasheets indicate that the switching converter can output 5V volts at its maximum. This controller contains 1 phases.
LM2727MTC Features
Transistor Driver Outputs
Switching Frequency: 50kHz~2MHz
Current Limit, Enable, Frequency Control, Power Good, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 90 %
Frequency: 2MHz
LM2727MTC Applications
There are a lot of Texas Instruments LM2727MTC DC to DC converter applications.
- PSRR circuits
- Overvoltage protection circuits in TV sets
- Computer-related products
- Grinders
- Sink circuits
- Computer application technology
- Scientific research
- Direct power supply system
- Hydrogen power
- Textile machinery
