LM2727MTC/NOPB
| Parameters | |
|---|---|
| Voltage - Supply (Vcc/Vdd) | 4.5V~5.5V |
| Quiescent Current | 1.5mA |
| Control Features | Current Limit, Enable, Frequency Control, Power Good, Soft Start |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 50kHz~2MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Nominal Input Voltage | 16V |
| Switcher Configuration | PUSH-PULL |
| Threshold Voltage | 4.2V |
| Max Frequency | 2MHz |
| Max Duty Cycle | 90 % |
| Clock Sync | No |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 58.910309mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Base Part Number | LM2727 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 5V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 16V |
| Input Voltage-Nom | 5V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20A |
LM2727MTC/NOPB Overview
The switching controller fits in the 14-TSSOP (0.173, 4.40mm Width) package and is ideal for most applications. There is enough capacity in the dc motor controller to generate the output for the 1 input. The pmic is packaged in Tube solid enclosure. A total of Transistor Driver dc switching's outputs can be handled by it. dc controls with 4.5V~5.5V voltage are supplied and operated. Suitable for a -40°C~125°C TJ dc switcher. In this switching controller, the switch can be set to 50kHz~2MHz. It is suitable for general dc dc regulator when it is set to Surface Mount. For efficient switching control, the dcdc regulator features Current Limit, Enable, Frequency Control, Power Good, Soft Start. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. DUAL are the position of the terminal of the switching converters. 14 terminations with a variety of function. Some of the control techniques adapted by these dc dc converter ics include PULSE WIDTH MODULATION. DC switcher's input voltageis set to 5V. You can find other relevant dc to dc converter ics by searching "LM2727". 14 pins are on switching converter. According to the test statistics, DC regulator outputs 5V voltage. The dc dc regulator's usual output current is 20A, which should be noted down when you start a project. Voltage regulator dc to dc is designed to operate at 90 % duty cycle during power-ups and power-downs to ensure reliability. This Surface Mount makes DC switcher suitable for most prototypes and applications. The max frequency of the pmic can reach 2MHz. To run the voltage regulator dc to dc safely and reliably, users should apply 16V to the voltage regulator dc to dc. When the dc switching is dormant, it uses 1.5mA. A nominal working status is achieved when the input voltage is set to 16V.
LM2727MTC/NOPB Features
Transistor Driver Outputs
Switching Frequency: 50kHz~2MHz
Current Limit, Enable, Frequency Control, Power Good, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 90 %
LM2727MTC/NOPB Applications
There are a lot of Texas Instruments LM2727MTC/NOPB DC to DC converter applications.
- Emergency lighting monitoring equipment
- Thermal power
- Direct power supply system
- Radio equipment
- Wide-range voltage regulation circuits
- Shearing machines
- Surge protection circuits
- Network technology
- Machining centers
- Telecommunications equipment
