LM27402MH/NOPB
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) Exposed Pad |
| Number of Pins | 16 |
| Weight | 62.709145mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Base Part Number | LM27402 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 18.6V |
| Output Type | Transistor Driver |
| Max Output Current | 30A |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 30A |
| Voltage - Supply (Vcc/Vdd) | 3V~20V |
| Quiescent Current | 4.5mA |
| Control Features | Current Limit, Enable, Frequency Control, Power Good, Soft Start, Tracking |
| Input Voltage (Min) | 3V |
| Topology | Buck |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 200kHz~1.2MHz |
| Input Voltage (Max) | 20V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Max Frequency | 1.35MHz |
| Max Duty Cycle | 95 % |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM27402MH/NOPB Overview
With a 16-TSSOP (0.173, 4.40mm Width) Exposed Pad package, the switching controller is suitable for a wide range of applications. For outputs of 1, this dc motor controller is suitable. Tube is the solid enclosure in which PMIC is packaged. There are Transistor Driver dc switching's output (s) that it can handle. 3V~20V is the operating voltage and supply voltage of the dc control. Suitable for work in a -40°C~125°C TJ dc switcher. The switching controller can be switched at 200kHz~1.2MHz. A generalization of dc dc regulator can be made using Surface Mount. Current Limit, Enable, Frequency Control, Power Good, Soft Start, Tracking provides dcdc regulator efficient switching control. Switch converters are connected to ICs with SWITCHING CONTROLLER analog outputs. Terminal (s) of the switching converters are designed at the DUAL position. A variety of 16 terminations are available in dc switching. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. DC switcher's input voltageis 12V volts. LM27402 can be searched for other relevant dc to dc converter ics. Switching converter has a total of 16 pins. It is recommended that the input voltage of the dc dc voltage regulator be 3V. DC regulator outputs 18.6V voltage based on test statistics. The dc to dc regulator can only accept a maximum input voltage of 20V. It's important to remember that the dc dc regulator's normaloutput current is 30A, so you should note it down when starting a new project. The duty cycle of the voltage regulator dc to dc can be set to 95 % on power-up or power-down to ensure reliability. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. There is a maximum frequency of 1.35MHz for this dc regulators. As long as the dc switching is in a dormant state, it utilizes 4.5mA. DC switchers cannot produce output currents greater than 30A.
LM27402MH/NOPB Features
Transistor Driver Outputs
Switching Frequency: 200kHz~1.2MHz
Current Limit, Enable, Frequency Control, Power Good, Soft Start, Tracking
PULSE WIDTH MODULATION
Max Duty Cycle: 95 %
LM27402MH/NOPB Applications
There are a lot of Texas Instruments LM27402MH/NOPB DC to DC converter applications.
- Post equipment
- Linear guide
- Arc suppression circuits
- Surge protection circuits
- CMM
- Scientific testing
- Packaging
- Telecommunications equipment
- Hydraulic presses
- Computer application technology
