LM27951SD
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-WFDFN Exposed Pad |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | DC DC Regulator |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Applications | Backlight |
| Subcategory | Display Drivers |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | LM27951 |
| Pin Count | 14 |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 3.3/5V |
| Nominal Supply Current | 1.5mA |
| Output Current | 30mA |
| Quiescent Current | 1.5mA |
| Voltage - Output | 2.5V~3.9V |
| Topology | Switched Capacitor (Charge Pump) |
| Min Input Voltage | 2.8V |
| Max Input Voltage | 5.5V |
| Internal Switch(s) | Yes |
| Dimming | PWM |
| Number of Segments | 4 |
| Switching Frequency | 750kHz |
| Voltage - Supply (Min) | 2.8V |
| Multiplexed Display Capability | NO |
| Touchscreen | Capacitive |
| Height | 800μm |
| Length | 4mm |
| Width | 3mm |
| Thickness | 800μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LM27951SD Overview
In order to save board space, the led driver uses the 14-WFDFN Exposed Pad package. Surface Mount is used for mounting the led light driver.As a DC DC Regulator, it has high efficiency and reliability.It is possible for the led driver ic to operate normally at -40°C~85°C TA.The benefits of Backlight are considerable.The system operates with a termination of 0.This LED driver is configured with a base of 14 pins.If the voltage supply is below 2.8V, undetermined failures may occur.The number of segments is estimated to be 4.The device has been mounted on the Surface Mount.It's under the LM27951 base part number.In this device, the output voltage is 2.5V~3.9V volts.There are 14 pins on this device.In addition, it can also be categorized into Display Drivers based on its characteristics.When the input voltage is set to 2.8V, it operates.Supply current cannot exceed 5.5V.You can supply 30mA current to the load.Powering systems requires 5.5V voltages.When the switching frequency is maintained at 750kHz, this electronic component is able to fully play its functions.A current of 1.5mA is consumed in the absence of external influences.
LM27951SD Features
Available in the 14-WFDFN Exposed Pad package
Operating temperature of -40°C~85°C TA
Supply voltage of 3.6V
Operating with the supply voltage of 5.5V
Switching frequency of 750kHz
LM27951SD Applications
There are a lot of Texas Instruments LM27951SD LED Driver ICs applications.
- Stage Lighting and Signage
- Power source for accessories such as car audios, car navigation systems, and ETC systems
- Refrigeration lighting
- Industrial LED Lighting: Image Recognition Devices
- Portable lighting
- General LED Lighting: Down-lights, Base-lights, Ceiling Lights, Exterior Lights
- Panel lighting
- Constant Voltage Power Source for portable equipment
- LED Lighting PFCs, Linear Dimmable
- White LED Backlight for portable equipment
