LM2902MT
| Parameters | |
|---|---|
| Lifecycle Status | NRND (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | LM2902 |
| Pin Count | 14 |
| Operating Supply Voltage | 13V |
| Number of Elements | 4 |
| Power Supplies | 5/26V |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 1.5mA |
| Output Current | 40mA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 45nA |
| Voltage - Supply, Single/Dual (±) | 3V~26V ±1.5V~13V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 7mV |
| Gain Bandwidth Product | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.25μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 26V |
| Voltage - Input Offset | 2mV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.25μA |
| Programmable Power | NO |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.05μA |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LM2902MT Overview
In the package, you will find a 14-TSSOP (0.173, 4.40mm Width)-case to contain the op amp ic. A General Purpose-type buffer amplifier is shown here. Upon delivery, op amp ic is packaged in a Tube case. The number of terminations approaches 14. The total number of pins on linear amplifier is 14. It is important to remember that this op amp should be operated at a voltage of 5V volts. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 14 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 7mV. Surface Mount is the recommended mounting type for this linear amplifier. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . Using a supply current of 1.5mA , this buffer op amp will be able to operate. There should be no change in the voltage gain at 100dB. For the operating supply voltage of the op amp ic, there is a rating of 4. The operating supply voltage of instrumentation amplifier is rated 13V voltage.
LM2902MT Features
14 Pins
supply voltage of 5V
100dB voltage gain
LM2902MT Applications
There are a lot of Texas Instruments LM2902MT Instrumentational OP Amps applications.
- Navigation
- Micro signal measurement
- High input resistance broadband
- Wireless base stations
- Band-stop filter
- Weak signal detection
- Television broadcasting equipment
- High/low-pass filter circuit
- Information processing
- Comparator
