LM2902VDR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 22 hours ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | LM2902 |
| Pin Count | 14 |
| Operating Supply Voltage | 16V |
| Number of Elements | 4 |
| Power Supplies | 5/30V |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 40mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 90nA |
| Voltage - Supply, Single/Dual (±) | 3V~32V ±1.5V~16V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 7mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.25μA |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM2902VDR2G Overview
A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. General Purpose-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tape & Reel (TR) case. We are approaching the 14h termination of the year. Linear amplifier has a total of 14 pins. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 14 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 7mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . An 1.4mA volt supply current is needed for this linear amplifier to operate. It is recommended to keep the voltage gain at 100dB at all times. A total of 4 elements are present in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 16V. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted.
LM2902VDR2G Features
14 Pins
supply voltage of 5V
100dB voltage gain
LM2902VDR2G Applications
There are a lot of ON Semiconductor LM2902VDR2G Instrumentational OP Amps applications.
- Active probe
- Measurements of Wheatstone bridge
- Television broadcasting equipment
- Semiconductor detectors
- Weighing systems
- Switching amplifier
- Precision measurement
- Automatic control
- Portable electronic products powered by batteries
- Broadcasting
