LM2904AVQDR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | LM2904 |
| Pin Count | 8 |
| Operating Supply Voltage | 13V |
| Number of Elements | 2 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 30mA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | 3V~26V ±1.5V~13V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 700 kHz |
| Unity Gain BW-Nom | 700 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.05μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM2904AVQDR Overview
There is a 8-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. This is a General Purpose type op amp. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. During the past two weeks, there have been close to 8 terminations. In this case, there are 8 pins on the board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. In total, the buffer amplifier consists of 8 pins. In terms of the input offset voltage, instrumentation amplifier rates at 1mV. The mounting type that is recommended for this electrical part is Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. As long as the supply current of the chip does not exceed 1mA, this op amp ic can operate. There should be no change in the voltage gain. There are 2 elements in this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 13V. It is used TR to pack the op amps.
LM2904AVQDR Features
8 Pins
supply voltage of 5V
100dB voltage gain
LM2904AVQDR Applications
There are a lot of Texas Instruments LM2904AVQDR Instrumentational OP Amps applications.
- Navigation
- MP3
- Communication
- Automation control systems
- Differentiator circuits
- Weak signal detection
- Semiconductor detectors
- Medical instruments
- Power generator
- Signal amplification
