LM2904DMR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~105°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | LM2904 |
| Pin Count | 8 |
| Operating Supply Voltage | 16V |
| Number of Channels | 2 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 40mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 45nA |
| Voltage - Supply, Single/Dual (±) | 3V~32V ±1.5V~16V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 7mV |
| Bandwidth | 1MHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Height | 950μm |
| Length | 3.1mm |
| Width | 3.1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM2904DMR2G Overview
There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case in which the instrumentation amplifier is packaged. This is a General Purpose type op amp. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. There have been a total of 8 terminations over the past year. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. There are 8 pins on this chip. Regarding input offset voltage, op amp rates 7mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~105°C when it comes to operating temperatureThis op amp can operate from a supply current at 1.5mA. Voltage gain should remain at 100dB. On the buffer amps, there are 2 channels that can be used. The operating supply voltage of instrumentation amplifier is rated 16V voltage. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
LM2904DMR2G Features
8 Pins
supply voltage of 5V
100dB voltage gain
LM2904DMR2G Applications
There are a lot of ON Semiconductor LM2904DMR2G Instrumentational OP Amps applications.
- Division circuits
- Vehicle electronics
- Hand-held batteries
- Polarized electrodes
- Commercial audio systems
- Radiation thermometry transducers
- Exponential operation circuits
- Signal amplification
- Navigation
- Image computer boards
