LM2904DRG3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | LM2904 |
| Pin Count | 8 |
| Operating Supply Voltage | 13V |
| Number of Elements | 2 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 30mA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 20nA |
| Voltage - Supply, Single/Dual (±) | 3V~26V ±1.5V~13V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 700 kHz |
| Unity Gain BW-Nom | 700 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Input Offset Current-Max (IIO) | 0.05μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LM2904DRG3 Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. The instrumentation amplifier in this picture is of the General Purpose-type. The op amp is delivered to you in a Tape & Reel (TR) case. A total of 8 terminations have been reported in the past few weeks. The pins on this board total to 8 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. A total of 8 pins are present on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 3mV. This electronic part is best mounted with type Surface Mount. With regard to operating temperature, op amp ranges -40°C~125°C. As long as the supply current of the chip does not exceed 1mA, this op amp ic can operate. Voltage gain should remain at 100dB. As a whole, there are 2 elements that make up this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 13V. For packing the buffer amplifier, the TR-axis is adopted.
LM2904DRG3 Features
8 Pins
supply voltage of 5V
100dB voltage gain
LM2904DRG3 Applications
There are a lot of Texas Instruments LM2904DRG3 Instrumentational OP Amps applications.
- Subtraction operation circuits
- High speed sample
- Measurements of Wheatstone bridge
- Multimedia playback equipment
- Signal amplification
- MP3
- Mobile phone
- Fast A/D and D/A converters
- Automatic control
- earphone
