LM2904MX
| Parameters | |
|---|---|
| Lifecycle Status | NRND (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e0 |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | LM2904 |
| Pin Count | 8 |
| Operating Supply Voltage | 16V |
| Number of Elements | 2 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 500μA |
| Power Dissipation | 530mW |
| Output Current | 30mA |
| Slew Rate | 0.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 45nA |
| Voltage - Supply, Single/Dual (±) | 3V~26V ±1.5V~13V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 7mV |
| Gain Bandwidth Product | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.05μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Input Offset Current-Max (IIO) | 0.05μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
LM2904MX Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. A General Purpose-type buffer amplifier is shown here. As far as the packaging is concerned, buffer op amp is delivered in a Cut Tape (CT) case. During the past two weeks, there have been close to 8 terminations. There are a total of 8 pins on this op amp. Please take in mind that this instrumentation amplifier should be run at 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. It has 8 pins that make up the linear amplifier. Op amp ic rates 7mV for input offset voltage. This electronic component is recommended to be mounted using the mounting type Surface Mount. With regard to operating temperature, op amp ranges -40°C~85°C. An 1mA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 100dB for the time being. According to the specifications of the buffer op amp, the operating supply voltage is rated at 2. The operating supply voltage of the buffer op amp is rated at 16V. For packing the buffer amplifier, the TR-axis is adopted.
LM2904MX Features
8 Pins
supply voltage of 5V
100dB voltage gain
LM2904MX Applications
There are a lot of Texas Instruments LM2904MX Instrumentational OP Amps applications.
- Ultrasound transducers
- Vehicle electronics
- Integrator circuits
- Car stereo
- Video amplifiers
- Medical instruments
- Portable media players
- Logarithmic operation circuits
- High input resistance broadband
- Television broadcasting equipment
