LM2904VDG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | RAIL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | LM2904 |
| Pin Count | 8 |
| Operating Supply Voltage | 16V |
| Number of Channels | 2 |
| Operating Supply Current | 1.5mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 40mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 50 dB |
| Current - Input Bias | 45nA |
| Voltage - Supply, Single/Dual (±) | 3V~32V ±1.5V~16V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 7mV |
| Bandwidth | 1MHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Power Supply Rejection Ratio (PSRR) | 50dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
LM2904VDG Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. An op amp ic of the General Purpose type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The number of terminations is approaching the 8 mark. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 5V volts. This particular linear amplifier is a type of Operational Amplifier device, to be precise. There are 8 pins on this chip. Op amp ic rates 7mV for input offset voltage. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureAs long as the supply current of the chip does not exceed 1.5mA, this op amp ic can operate. 100dB should be the voltage gain. 2 channels are available on the instrumentation amplifier. The operating supply voltage of instrumentation amplifier is rated 16V voltage. RAIL is adopted to pack the instrumentation amplifier.
LM2904VDG Features
8 Pins
supply voltage of 5V
100dB voltage gain
LM2904VDG Applications
There are a lot of ON Semiconductor LM2904VDG Instrumentational OP Amps applications.
- Signal transformation
- Video conversion and routing
- Commercial audio systems
- Blood pressure sensors
- Power generator
- Integrator circuits
- Non-polarized electrodes
- High/low-pass filter circuit
- Logarithmic operation circuits
- High input resistance broadband
