LM324ADR2
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LM324A |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 16V |
| Number of Elements | 4 |
| Power Supplies | 5/30V |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 40mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 45nA |
| Voltage - Supply, Single/Dual (±) | 3V~32V ±1.5V~16V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.2μA |
| Power Supply Rejection Ratio (PSRR) | 65dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.1μA |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
LM324ADR2 Overview
Packaging for the buffer amplifier is in the form of a 14-SOIC (0.154, 3.90mm Width) case. This is a General Purpose type op amp. The op amp is delivered to you in a Cut Tape (CT) case. We are approaching the 14h termination of the year. Buffer amplifier has a total of 14 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. A total of 14 pins are present on the instrumentation amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 3mV. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, op amp ranges 0°C~70°C. Operational amplifier can operate supply current at 1.4mA. Keeping the voltage gain at 100dB is the best course of action. There are a total of 4 elements in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 16V voltage. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
LM324ADR2 Features
14 Pins
supply voltage of 5V
100dB voltage gain
LM324ADR2 Applications
There are a lot of ON Semiconductor LM324ADR2 Instrumentational OP Amps applications.
- Proportional counter tubes
- Weak signal detection
- Biopotential
- Power control
- Semiconductor detectors
- MP3
- Test and measurement instruments
- Inverse/same-phase proportional circuit
- Automatic control
- Measurements of Wheatstone bridge
